Remko MHP-Manager Wireless Remote Control Manuel d'utilisateur Page 1

Edition GB –B09REMKO WIRELESS REMOTE CONTROL FOR MULTITALENT HEAT PUMP MANAGEROperation - Technology - Spare parts

Heating circuit 1/2Parameter Function CommentsActual/Target room temp.Current room temperature according to heating programme and operating modeRoom t

User menuSystemThis menu contains all the settings which can be adjusted by the user of the system.Parameter Value range Default OV*) CommentsLanguage

Heating circuit 2Parameter Value range Default OV CommentsTarget room temp. 1 *) 5°C - 40°C 20°CAdjust the desired room temperatureTarget room temp. 1

ParameterValue rangeDefault OV CommentsHeating curve 0.00 - 3.00 1.20The curve's slope indicates by how many degrees the supply temperature will

Parameter Value range Default OV CommentsRoom influence 00 - 20 10The room sensor influence is only active when the analogue room device FBR (room senso

Heating period 1 Heating period 2 Heating period 3MonTuesWedThursFriSatSunTime programmes menuAdjusting a time programmeAll time programmes can be set

Heating period 1 Heating period 2 Heating period 3MonTuesWedThursFriSatSunHeating programme 2 => Factory setting: Mon to Fri: 6:00am to 8:00am, 4:

Parameter Function CommentsTime (hh:mm) Set hour, F-key [==>], hh:mm, set minutes(Not with a time master or DCF in the system)The clock may lose up

Service menuValues (parameters) are summarised here in order to enable quick access for customer service.Parameter CommentsSoftware number XXX.XXSoftw

Parameter Value range Default OV CommentsChange code 0000 - 9999 0000This is where you can change the default code number [0000] => protection agai

Parameter Value range Default OV CommentsMin limit *)00 = On 01 = Off 02 = Permanent00HA minimum limit(not in cascade operation)Reduces condensate for

Parameter Value range Default OV CommentsCharge pump lock Off/On OnThe charge pump is only switched on once the HA temperature has exceeded the tank t

Parameter Value range Default OV CommentsHC functionDefault, Const. supply temp.DefaultHeating circuit function selectionDefault => default heating

Parameter Value range Default OV CommentsMax supply temp. 20°C - 110°C 55°CThe calculated target supply temperature for the heating circuit is limited

General mode of operationHeating circuit regulationWeather-based regulation The set heating curve is used to determine the boiler or supply temperatur

Troubleshooting and customer serviceThe units and components are manufactured using state-of-the-art production methods and tested several times to v

Only the error with the highest priority is displayed.- The message "Error" appears on the standard display and the error number in the Fav

1. Read this manual carefully before commissioning.2. Fit the controller (see chapter “Installation”).3. Wait until the message Installation appear

Changing the batteryIf the battery symbol shown below displays 0%, the battery should be changed within the next week.100% 50% 0%System busHeating sys

Technical dataRadio frequency MHz 868,0 - 868,6Max. transmission power mW 4Supply voltage 2x LR6 alkaline cellPower consumption mA 0,15Protection cate

ContentsRead these operating instructions carefully before commissioning/using the unit!These instructions are an integral part of the unit and must a

Notes

Notes

We reserve the right to make technical changes and provide no warranty as to the accuracy of this data!ConsultationThanks to intensive training, our c

Safety notesWarranty The precondition for all warranty claims is that the orderer or his customer has fully filled out the "warranty registration

Controls during normal operation The wireless remote control is controlled with the following keys.The rotary knob (A) can be used to toggle between t

(Heating OFF and Water heating OFF, Frost protection function only)Setting the operating modeDuring normal operation, press the F-key next to “OK”.Aut

Controls in operating modeCBAIf a parameter, a function/display or a parameter menu is not supported by the connected heating circuit controller, it i

Overview of the operating menusMenus Description Sub-menus DescriptionDisplayDisplays system values (e.g. sensor and target values). Adjustment is not

Display menuThe parameters are selected using the rotary knob. (HA = heating appliance)SystemParameter Function CommentsOutdoor temp. Displays the ou